Home | Products | Testimonials | FAQ | Directions | Gallery | Become a Distributor | Contact Us

Directions For Using DRI WASH 'n GUARD® Products.

 

Directions For Using DRI WASH 'n GUARD® Products.

Directions for Filling the AIRosol Application Bottle

1. Shake the bottle of DRI WASH 'n GUARD® vigorously for 15-20 seconds, or until all product that adheres to bottom of storage bottles has mixed in.
2. Pour DRI WASH 'n GUARD® into the AIRosol pump sprayer until the bottle is approximately 3/4 full.


Directions for Using DRI WASH 'n GUARD® ULTRA-ION™ Waterless Car Wash by Hand Application

 

1. Apply DRI WASH 'n GUARD® ULTRA-ION™ Waterless Car Wash to a cool, dry surface in a shaded area, out of wind if possible.
2. Use two clean 100% cotton terry cloth towels... one for applying the product and one for buffing. For best results, use a micro fiber towel for buffing.
3. Invert the bottle and shake vigorously for 15-20 seconds.
4. Pressurize the bottle by pumping the cap up and down until a strong resistance is felt (approx. 10-15 times).
5. Spray a light coat of DRI WASH 'n GUARD® on a small section of vehicle (2-3 sq. ft.), spraying with a broad sweeping motion where possible. 6. Using the terry cloth towel, with moderately firm pressure rub polish thoroughly over the sprayed area until the filmy haze that appears almost disappears. 7. Immediately buff remaining haze to a high gloss with buffing towel.
 
Directions for Use by Machine Application

1. Use a conventional or orbital-type buffer equipped with a foam polishing pad. Do not exceed 1,500 RPM.
2. Apply DWG ULTRA-ION™ as described in steps 3, 4, and 5 above. Immediately buff sprayed area to a high gloss.
3. Continue until all accessible areas have been buffed. Polish any remaining areas by hand, if necessary.

Directions for Using DRI WASH 'n GUARD® CLASSIC Car Wash by Hand Application

1. Apply DRI WASH 'n GUARD® CLASSIC Waterless Car Wash to a cool, dry surface in a shaded area, out of wind if possible. 2. Use two clean 100% cotton terry cloth towels... one for applying the product and one for buffing. For best results, use a micro fiber towel for buffing.
3. Invert the bottle and shake vigorously for 15-20 seconds.
4. Pressurize the bottle by pumping the cap up and down until a strong resistance is felt (approx. 10-15 times).
5. Spray a light coat of DRI WASH 'n GUARD® on a small section of vehicle (2-3 sq. ft.), spraying with a broad sweeping motion where possible.6. Using the terry cloth towel, with moderately firm pressure rub polish thoroughly over the sprayed area until the filmy haze that appears almost totally disappears.
7. Immediately buff remaining haze to a high gloss with buffing towel.

Directions for Use by Machine Application

1. Use a conventional or orbital-type buffer equipped with a foam polishing pad. Do not exceed 1,500 RPM.
2. Apply DWG ULTRA-ION™ as described in steps 3, 4, and 5 above. Immediately buff sprayed area to a high gloss.

3. Continue until all accessible areas have been buffed. Polish any remaining areas by hand, if necessary.

DRI WASH 'n GUARD® All Weather Tire Treatment

DO NOT use on glass, Plexiglas, mirrors, chrome or other non-porous surfaces.
DO NOT use in an area where painting occurs or on surfaces that may require painting.
DO NOT mix this product with any other chemicals or liquids.
First: Replace shipping cap with trigger sprayer (included).
 
Directions:
 
1. Use one soft, clean cloth for cleaning/polishing and another for buffing.
2. Invert bottle and shake once.
3. Rotate nozzle to "SPRAY" position.
4. Spray generously onto surface from a distance of approximately 8-10 inches.
5. Immediately polish the are with a soft, clean cloth. The use of a small, soft bristle brush may be helpful in penetrating rough or uneven surfaces such as tire sidewalls.
6. Buff to a shine using a second soft, clean cloth.
7. Repeat process for higher luster and longer lasting protection.

DRI WASH 'n GUARD® Leather and Vinyl Treatment
 
DRI WASH 'n GUARD® Leather and Vinyl Treatment contains no petroleum distillates, soaps or detergents. It is non-corrosive, non-flammable, and non-caustic.
DO NOT use on glass, floors, woven materials or painted surfaces.
DO NOT mix this product with any other chemicals or liquids.
For best results, pre-test on inconspicuous area before use.
 
Directions:
 
1. Use one soft, clean terry cloth towel or sponge for cleaning, and another for buffing.
2. Invert bottle and shake once or twice.
3. Spray area to be cleaned from a distance of 8-10 inches. To prevent overspray, apply to an area no larger than 18 inches.
4. Rub sprayed area with a soft, clean terry cloth towel or sponge. (For excessively soiled areas, scrub lightly with a soft brush and then rub with a clean soft terry cloth towel or sponge.)
5. For best results, buff lightly with a clean, terry cloth towel.

 


DRI WASH 'n GUARD® Upholstery, Fabric and Carpet Treatment

 

DO NOT use on glass, floors, or painted surfaces.
DO NOT mix this product with any other chemicals or liquids.
For best results, pre-test on inconspicuous area before use. Directions:
 
1. Use one soft, clean terry cloth towel or soft bristle brush for cleaning, and another for drying
2. Invert bottle and shake once or twice.
3. Spray area to be cleaned from a distance of 8-10 inches.
4. Agitate sprayed area with soft, clean, terry cloth towel or bristle brush.
5. Pat dry with soft, clean, terry cloth towel.
6. Allow area to completely dry.

DRI WASH 'n GUARD® Premium Metal Polish
 
DO NOT use on thin plated metal surfaces.
DO NOT use near heat, sparks, or flame.
DO NOT breath vapors for extended periods.
DO NOT mix this product with any other chemicals or liquids.
For best results, pre-test on inconspicuous area before use.
 
Directions:
 
1. Use two soft, clean terry cloth towels... one for cleaning/polishing and one for buffing.
2. Invert bottle and shake vigorously before and during use.
3. Apply a small amount of DRI WASH 'n GUARD® Premium Metal Polish on a clean terry cloth towel.
4. Rub surface lightly until polish turns dark.
5. Let dry and buff with a separate clean, terry cloth towel.
6. For maximum protection, apply DRI WASH 'n GUARD® Waterless Car Wash and Protective Glaze after treatment.

DRI WASH 'n GUARD® OxyGone™
 
For best results, pre-test on inconspicuous area before use.
 
Directions:
 
By Hand:
 
1. Invert bottle and shake vigorously for 5 seconds
2. Apply a small amount of OxyGone™ on a clean terrycloth towel.
3. Using the towel, work the product into the oxidized surface until haze begins to disappear.
4. Using another clean terry cloth towel, buff the treated surface to a gloss.
5. For best results, work in small sections.
 
Directions by Machine:
 
1. Invert bottle and shake vigorously for 5 seconds.
2. To prevent splatter, apply a small amount of OxyGone™ on a clean terrycloth towel and spread over a 12" area.
3. Buff to a high gloss using a conventional or orbital-type buffer equipped with a foam polishing pad. Do not exceed 2,400 RPM.